How To Change A Garage Door Opener

Download Commodity

Download Article

Tired of opening your garage door past paw? Try installing a garage door opener yourself instead of paying someone else to practice information technology. Installation should but take you a few hours to complete and having a garage door opener will make opening and closing your garage door every day then much quicker and easier.

1. one

   Assess whether you accept the type of garage door that can accept an opener attached. Well-nigh newer garage doors with multiple horizontal sections should exist compatible with an opener. Older types, such as those that are one solid piece, may need to be replaced before you can install an opener.^[ane]

2. 2

   Choose a garage door opener. In that location are two bones types of garage door openers, concatenation driven and chugalug driven. Both operate in roughly the same way only just use a slightly dissimilar office for operation.

   • A chugalug driven garage door opener can be a bit quieter during functioning. Consider this when making the choice of what opener to purchase.

   Advertisement

3. 3

   Prepare your garage door for opener installation. Brand sure your garage door is well lubricated and operating properly.

   • The weight of a garage door is supported past the door springs, cables, and pulleys, not the opener. If y'all can't raise and lower the door normally by manus, do not install the opener until the door is repaired.
   • Remove all ropes or cords attached to the garage door so you won't get tangled in them during installation.
   • Deactivate or remove all existing garage door locks, so they won't accidentally appoint and either impairment the opener or cause personal injury.

4. four

   Make sure there is an electrical plug in the immediate area of the opener motor. They are usually mounted in the ceiling, facing down. You will need to install one, or have one installed by a licensed electrician, if you exercise non have one already.

   • If y'all demand to install permanent electric wiring, always disconnect the power at the main billow box before attempting to wire connections. Always connect the power cord of the garage door opener to a properly grounded outlet to avoid electric shock.

   Advertising

1. 1

   Lay out all of the parts your opener came with. Make sure that the parts list included with your opener matches the parts included in the bundle.

2. two

   Begin by putting together the primary assembly. Your opener should have come with a list of detailed installation instructions, and so follow those to brainstorm assembly.

   • First put the rail together. This should come in several pieces that fit easily together.^[2] Attach them together every bit directed in your installation instructions.
   • Then yous volition demand to slide the wagon (besides known as a trolley) over the rails. This is the piece of the opener that will motility along the rail, pulling the door open.
   • Attach the track to the motor compartment. This is the largest piece of the opener and it will be positioned furthest from the garage door.
   • Install the pulley at end of track, opposite the motor compartment. So feed the belt or chain through the end of the rail, around the pulley, then around the other end (at the motor). Finally you will attach the end of the belt or chain to the carriage. The finish of the chain or chugalug should have a screw attached to it, so that you lot can hands attach information technology to the railroad vehicle. This screw will also allow you to adapt the tension of the chain or belt.^[3]

3. 3

   Install blocking on the ceiling, if in that location is none in that location already. This is how you will attach the garage door opener to the ceiling. The instructions your garage door opener came with should have detailed specifications for the blocking.

   • No thing what the size and spacing of the blocking is, be sure that you lot are attaching it to joists (solid wood) in the ceiling, not simply to sheetrock.

4. 4

   Find the point of connection to the garage door and attach the bracket that came with your opener to the door itself. The distance from the top of the garage door should exist specified in the opener'south direction and in most cases you will want it centered on the door.

   • If your garage door opener did not come up with this subclass y'all will need to consult the instructions to determine what blazon of bracket you lot will need.^[iv]

5. 5

   Lean the end of the assembly (reverse the motor compartment) up above the garage door. Attach the bracket the opener came with to the wall above the door and then insert the end of the assembly into it. Connect the bracket and the stop of the associates every bit directed in the installation instructions.

6. six

   Elevator the other end of the assembly upward and into place. Install the power unit high enough and so that tall people won't run into it, at least 7' from the floor if possible.

7. seven

   Adhere to the bracket on the garage door. In many cases at that place will be 2 pieces used to attach the door to the opener, giving some flexibility in the connection, every bit the distance betwixt the door and the opener assembly may vary.

   Ad

1. 1

   Attach the rubber rope to the emergency release on the carriage. Garage door openers must have a manual disconnect string. It should be adjusted to approximately 6' from the floor so any adult tin attain it.

2. 2

   Insert a lightbulb into the socket in the garage door opener compartment, if it has 1. The transmission or the inside of the compartment should advise an appropriate wattage for the lightbulb but it'due south a good idea to purchase a lightbulb that is rated for "crude service" because of the vibrations information technology will need to withstand.^[5] The calorie-free volition turn on whenever the door is opened but may exist able to be operated manually as well.

   • Many garage door openers apply the light to bespeak programming changes that are occurring. Exist certain to install the lightbulb in your opener then that you can program your garage door successfully.

3. 3

   Install the electric eye safety system that came with your garage door opener. This volition crave you to run ii small wires downwards to the bottom of one side of your garage door. You volition likewise need to mount an electric eye at that place, besides as a reflector on the opposite side of the door.

   • Be certain to follow the instructions and wiring diagram included with your opener.

4. four

   Install the push push control 5' from the floor so small children cannot reach it. Put it in a location where anyone operating information technology tin can easily see the garage door.

   • Also install and plan any other optional equipment, such as a keypad for opening the door on the exterior of your garage or remote openers.

5. v

   Adjust the safety contrary system and the electric heart system properly. Refer to your opener manufacturer's instructions for details.

6. half dozen

   Test your garage door to make certain the opener is working correctly. If the door and the opener are moving smoothly, if all parts are fastened solidly, and there are no obstructions blocking the door or the opener's movement, then information technology should be fine.

   • Some garage door openers tin exist quite loud nether normal working conditions, so don't presume that but because information technology's a fleck loud that it is not installed properly.

   Advertising

Add New Question

• Question

  How can l stop the rail from angle upward when I close the door?

  

  It sounds similar the travel limits need to be reset. The operator is trying to push the door through the floor, and since it cannot, the runway is being pushed up.

• Question

  Does a garage door opener need to be installed on a rail?

  

  Yes. The rail that you tin can see in the pictures helps elevator the door, considering the opener volition take the tension off of the cables. It also is used to guide the concatenation/belt.

• Question

  How long does it have to install a garage door opener?

  

  About a one-half an hr.

• Question

  How exercise I install an external garage door opener?

  

  Mount the opener on a wall about the garage door, and connect the external system with the internal garage door opener.

• Question

  How practice I set the wiring for condom sensors for my garage door?

  

  Consult the installation manual that came with the equipment. If yous do non have the installation transmission, y'all can commonly obtain a copy from the manufacturer'due south website.

• Question

  Does the associates bar have to exist level for the garage door to close?

  

  No, when the door is open, the rail should exist 1.five inches above the console. A level rails can cause damage to the door.

Ask a Question

200 characters left

Include your email accost to get a message when this question is answered.

Submit

Advertisement

Video

• Always defer to the installation directions included with your garage door opener. They are written for your specific opener, while the directions included here are more general.

• If you lot meet damage to any office of the opener, don't use it until it has been repaired by a qualified service technician. Never operate the door if the safety arrangement is not functioning properly.

• Check the safety contrary organization and the electric eye once a month, and readjust it if necessary. Periodically check the manual operation of the door likewise.

• Reinforce lightweight fiberglass or metallic garage doors before installing an opener to prevent damage to the door and insure that the safety opposite system will operate properly.

• Operate a garage door just when information technology is free of any obstructions.

Thanks for submitting a tip for review!

Advert

• If possible, utilise the manual disconnect just when the garage door is fully closed. The opener will non carry the weight of the door, and if the springs are weak or broken, disconnecting information technology could cause the door to fall.

• Never let children operate or play with the opener. Keep the radio transmitter in a location inaccessible to children.

• Do not vesture rings, watches or loose wear while installing or servicing a garage door or opener. They could become caught on a moving part and cause injury to you or your property.

• E'er disconnect electrical power to the opener when servicing the unit of measurement or working close to the drive concatenation or other moving parts.

• Never change or remove a garage door's springs, cables, or pulleys. Doors with torsion springs (a single ringlet to a higher place the door) should only exist serviced by qualified service technicians.

Advertisement

About This Commodity

Article Summary 10

To install a garage door opener, get-go assemble the rail, carriage, caster and motor compartment according to the instructions. Attach brackets to the ceiling and door, and position the end of the rails to a higher place the closed door. Elevator the motor compartment into place on the ceiling, and attach the rail and railroad vehicle to the subclass on the door. For added prophylactic, adhere a rope to the emergency release on the carriage. For more than tips, including how to install a keypad entry panel and sensors, whorl down!

Did this summary help you?

Thanks to all authors for creating a page that has been read 180,411 times.

Did this commodity assistance you lot?

Source: https://www.wikihow.com/Install-a-Garage-Door-Opener

Posted by: truesdalehimat1991.blogspot.com

Share this post